Turbidity is a measure of how much suspended particles in water scatter light — and it is one of the most widely regulated water quality parameters worldwide. From drinking water plants to industrial effluent discharge, accurate turbidity measurement requires understanding the measurement standards (NTU, FNU, FTU), choosing the right instrument, and following proper sampling technique. This guide explains the standards, compares turbidity meter types, and provides a practical selection framework.
1. What Is Turbidity and Why Does It Matter?
Turbidity is caused by suspended particles such as silt, clay, organic matter, algae, and microorganisms. High turbidity:
- Reduces the effectiveness of disinfection (pathogens hide behind particles).
- Indicates filter breakthrough in drinking water treatment.
- Affects aquatic ecosystems by reducing light penetration and clogging fish gills.
- Triggers regulatory non-compliance if discharge limits are exceeded.
2. Turbidity Units: NTU, FNU, FTU, and Others
Multiple turbidity units exist because different standards specify different instrument geometries and light sources:
- NTU (Nephelometric Turbidity Unit): Based on EPA Method 180.1 — uses a tungsten (white) light source and measures scattered light at 90°. The most commonly referenced unit in North America.
- FNU (Formazin Nephelometric Unit): Based on ISO 7027 — uses a near-infrared (860 nm) LED and measures at 90°. Numerically equivalent to NTU for formazin standards, but less affected by colored dissolved matter. Preferred internationally.
- FTU (Formazin Turbidity Unit): An older term; 1 FTU ≈ 1 NTU ≈ 1 FNU when calibrated with formazin.
- JTU (Jackson Turbidity Unit): Historical; based on visual candle turbidimeters. Obsolete but sometimes referenced in legacy regulations.
Key point: NTU and FNU are not always interchangeable in colored water samples. When a regulation specifies a particular unit, use an instrument that complies with the corresponding standard (EPA 180.1 for NTU; ISO 7027 for FNU).
3. How Turbidity Meters Work
A nephelometric turbidity meter shines a light beam through a sample and measures the intensity of light scattered at 90° to the incident beam. The scattered intensity is proportional to turbidity. Advanced models add detectors at additional angles (0°, 135°, 180°) for ratio measurement, which improves accuracy at very low and very high turbidity levels.
4. Types of Turbidity Meters
4-1. Portable (Handheld)
- Battery-powered, IP67-rated, field-ready.
- Sample cuvette or flow-through cell.
- Range: typically 0–1,000 NTU (some to 4,000 NTU).
- Best for: Field sampling, plant rounds, environmental compliance checks.
4-2. Benchtop (Laboratory)
- AC-powered, high-precision, EPA/ISO compliant.
- Ratio-mode nephelometry for low-turbidity drinking water (< 1 NTU).
- Data logging with GLP audit trail.
- Best for: Drinking water lab compliance, filter performance testing, R&D.
4-3. Online (Process)
- Submersible probe or flow-through cell with transmitter.
- Continuous 4–20 mA / digital output to PLC/SCADA.
- Auto-cleaning (wiper or ultrasonic) to prevent fouling.
- Best for: Filter outlet monitoring, effluent discharge, intake water screening.
5. Regulatory Turbidity Limits (Examples)
| Application | Limit | Standard |
|---|---|---|
| Drinking water (US EPA) | ≤ 1 NTU (95 % of samples); never > 4 NTU | EPA SWTR |
| Drinking water (WHO) | < 1 NTU ideally; < 5 NTU acceptable | WHO Guidelines |
| Effluent discharge (typical) | 10–50 NTU (varies by jurisdiction) | Local permit |
| Swimming pools | ≤ 0.5–1.0 NTU | Local health code |
6. Selection Checklist
- Which standard? EPA 180.1 (NTU) or ISO 7027 (FNU)? Match the instrument to your regulatory requirement.
- Range needed? Low-range (< 40 NTU) → ratio nephelometer; wide-range (0–4,000 NTU) → standard nephelometer.
- Deployment? Lab → benchtop; field → portable; continuous → online.
- Colored samples? ISO 7027 (IR light) is less affected by sample color than EPA 180.1 (white light).
- Compliance? Ensure the instrument has traceable calibration with formazin or approved polymer standards (StablCal, AMCO-AEPA).
Explore Turbidity Meters
Sechang offers turbidity meters across portable, benchtop, and online categories — EPA 180.1 and ISO 7027 compliant. Our team can help select the right instrument and calibration standards for your water quality program.
8. Turbidity Measurement Methods: Which to Use
Turbidity can be measured by four main optical methods. The right choice depends on the turbidity range and regulatory requirements:
| Method | Detector angle | Best range | Standard |
|---|---|---|---|
| Nephelometric (90°) | 90° scattered light | 0–1,000 NTU | ISO 7027 / EPA Method 180.1 |
| Ratio turbidimetry | 90° + multiple angles | 0–10,000 NTU | EPA Method 180.1 (ratio mode) |
| Transmitted light | 0° (attenuation) | > 500 NTU | High-turbidity applications |
| Backscatter (180°) | Backscattered light | Wide range, online | Wastewater, sludge blanket |
For drinking water compliance (WHO, US EPA, EU), nephelometric measurement at 90° with white or infrared light is required. ISO 7027 specifies infrared (860 nm) light — preferred for colored samples because infrared is unaffected by sample color, eliminating false-high readings in tea-colored or humic-rich source waters.
9. Turbidity Meter Maintenance and Verification
- Cell cleaning: Fingerprints, scratches, and chemical residues on the sample cell cause significant errors. Clean with soft lens tissue. Never use abrasive materials.
- Secondary standards: Once Formazin is prepared and standardized, store secondary standards (sealed, away from light) for routine daily verification. Replace when values drift > 2 %.
- Online sensor cleaning: Air wiper, mechanical brush, or ultrasonic cleaning systems extend service intervals in high-turbidity wastewater streams.
- Lamp/LED lifespan: LED-based turbidimeters have lamp lifetimes exceeding 10 years under normal use. Traditional tungsten lamp instruments require periodic bulb replacement.
10. Turbidity Limits by Application
Understanding regulatory and process turbidity limits helps calibrate the instrument range correctly:
| Application | Typical turbidity limit | Standard |
|---|---|---|
| Drinking water (treated) | ≤ 0.3 NTU (US); ≤ 1 NTU (WHO) | US EPA, WHO Guidelines |
| Surface water (Class A) | ≤ 2–5 NTU | Regional environmental regulation |
| Industrial cooling water (filtration check) | ≤ 1–5 NTU | Process specification |
| Semiconductor ultrapure water | ≤ 0.1 NTU | SEMI F63 |
| Wastewater effluent (TSS proxy) | Varies; often 10–50 NTU | Discharge permit specific |
| Swimming pools | ≤ 0.5 NTU (pool bottom visible from deck) | US CDC, local regulation |
11. Online Turbidity Analyzers for Process Control
For continuous process monitoring — filter effluent polishing, membrane integrity monitoring, clarifier performance — online turbidity analyzers provide real-time data to control systems:
- Flow-through cells: Sample pumped past the sensor in a closed cell. Eliminates ambient light interference; provides stable signal for process control.
- Submersible probes: Directly immersed in the process stream or tank. Lower installation cost; requires clean sensor face maintenance.
- Signal output: 4–20 mA, Modbus, HART — connects to SCADA or PLC for alarm generation and automatic filter backwash control.
- Automatic cleaning: Air wiper systems inject a brief air burst to clear the optical window. Ultrasonic transducers prevent biofilm adhesion. Both extend calibration intervals and reduce operator intervention.
▶ Browse Turbidity Meters & Request a Quote
12. Selecting a Turbidity Meter: Checklist
Use this checklist before finalizing your turbidity meter purchase:
- ☐ Measurement range covers your expected turbidity values (include peak turbidity events, not just typical)
- ☐ Detection method matches regulatory requirement (90° nephelometric per ISO 7027 or EPA 180.1)
- ☐ Light source wavelength appropriate: infrared (860 nm) for colored samples; white light for clear water
- ☐ Stray light specification < 0.015 NTU for drinking water compliance instruments
- ☐ Calibration standard type: Formazin (primary), StablCal (secondary), AMCO-AEPA (secondary)
- ☐ Sample cell material (borosilicate glass for lab; polycarbonate for field)
- ☐ IP rating if used in field or wet environments (minimum IP54 for portable field meters)
- ☐ Data output format: manual reading, USB, Bluetooth, or 4–20 mA for process control
- ☐ Bubble trap or degassing feature if measuring gassy samples
- ☐ Anti-fouling and cleaning system if used as an online analyzer
Sechang offers a broad selection of turbidity meters and analyzers — from portable benchtop units for drinking water quality verification to online process analyzers for filter performance monitoring in water treatment plants.
▶ Browse Turbidity Meters — Get a Quote
13. Requesting a Turbidity Meter Demonstration
Before purchasing a turbidity meter for critical applications — drinking water compliance, filter monitoring, or environmental regulatory reporting — arrange a demonstration with your actual water sample matrix. Bring samples at different turbidity levels representative of your process range, including low-turbidity polished water (where stray light specifications matter most) and high-turbidity inlet water. Test the repeatability of five consecutive readings on the same sample. For online applications, ask the supplier to demonstrate the sensor's cleaning cycle and verify the output signal integrates correctly with your SCADA or data logger. Document the results for your instrument qualification records. A thorough pre-purchase evaluation with real samples is the most reliable predictor of long-term measurement performance in your specific application.
Our application engineers are available by phone, email, and on-site — ready to help you identify the ideal solution for your specific measurement challenge.Contact us today to discuss your measurement requirements, request a product demonstration, or receive a customized quotation. Our team will respond within one business day with instrument recommendations matched to your budget, accuracy requirements, and site conditions.
Measurement quality starts with the right instrument choice — and our turbidity specialists are here to guide you every step of the way, from initial selection through long-term operational support.
▶ Need help choosing the right instrument? Contact Sechang for expert advice and a quotation