MLSS Analyzer and Sludge Concentration Meter: Mixed Liquor Suspended Solids Monitoring for Activated Sludge Process Control

Mixed liquor suspended solids (MLSS) concentration is the central process variable in activated sludge wastewater treatment. The biomass concentration in the aeration tank — typically maintained between 2,000 and 5,000 mg/L in conventional activated sludge systems — directly determines treatment capacity, oxygen demand, sludge production, and effluent quality. Maintaining the correct MLSS range requires continuous measurement and responsive control of the waste activated sludge (WAS) removal rate.

Historically, MLSS was monitored through manual grab sampling and laboratory gravimetric analysis (APHA Method 2540D), with results available every 4–8 hours. Online MLSS analyzers and sludge concentration meters now provide continuous real-time data, enabling direct feedback control of WAS pumps and optimization of sludge retention time (SRT) — the most powerful lever available for activated sludge process management.

Not sure which instrument fits your site?

▶ Get a fast quote — contact our engineers

MLSS and Its Role in Activated Sludge Process Control

Activated sludge relies on a mixed culture of microorganisms — primarily bacteria, protozoa, and fungi — maintained in suspension in the aeration basin. These organisms metabolize dissolved and colloidal organic matter (BOD), oxidize ammonia to nitrate (nitrification), and in enhanced biological processes, remove phosphorus and denitrify nitrate. The concentration of these organisms is directly proportional to MLSS (or more specifically, MLVSS — mixed liquor volatile suspended solids, the organic fraction of MLSS).

Key relationships governed by MLSS:

  • Food-to-microorganism ratio (F/M): F/M = BOD loading rate ÷ MLVSS × HRT. As MLSS rises, F/M falls, reducing metabolic rate but improving effluent quality. Low F/M (high MLSS, long SRT) favors nitrification and biological phosphorus removal
  • Sludge retention time (SRT): SRT = (MLSS × aeration basin volume) ÷ (WAS flow × WAS concentration). SRT must exceed the minimum growth time for nitrifiers (~10 days at 15°C) for stable nitrification
  • Oxygen demand: Higher MLSS means more biomass and higher oxygen uptake rate (OUR); aeration system sizing depends on maintaining oxygen transfer capability above the peak OUR at maximum MLSS
  • Sludge settleability: Above a critical MLSS concentration (typically 3,500–5,000 mg/L in conventional clarifiers, higher in MBR systems), secondary clarifier hydraulic loading limits increase the risk of sludge blanket rise and effluent solids carryover

Online MLSS Measurement Technologies

Infrared Turbidity/Suspended Solids Sensors

Near-infrared (NIR) optical sensors are the most widely used technology for online MLSS measurement in activated sludge systems. These sensors transmit an infrared light beam (typically at 860 nm wavelength) through the mixed liquor and measure the backscattered light intensity returned to the detector. The backscatter signal is proportional to the concentration of suspended particles.

Operating principle: Unlike transmission-based turbidimeters (which measure light that passes through the sample), backscatter sensors measure light reflected from suspended particles toward the source. This design makes them more robust at high suspended solids concentrations (1,000–50,000 mg/L) where transmitted light intensity would be too low to measure accurately.

Measurement performance:

  • Range: 0–50,000 mg/L (with appropriate factory calibration)
  • Accuracy: ±3–5% of reading in the 1,000–10,000 mg/L range
  • Response time: Continuous (no discrete cycle time)
  • Requires site-specific calibration against gravimetric MLSS values (laboratory TSS analysis of grab samples)

Limitations: NIR backscatter sensors measure optical turbidity, not true mass concentration. The relationship between backscatter signal and MLSS depends on particle size distribution, particle color (dark biomass scatters differently from white mineral particles), and biofilm characteristics — all of which vary between facilities and over time. Regular recalibration (typically every 1–3 months) is required to maintain accuracy.

Ultrasonic Concentration Sensors

Ultrasonic suspended solids sensors transmit an ultrasonic pulse through the sample and measure the attenuation of the signal. Ultrasound attenuation is proportional to particle concentration and is less sensitive to particle color than optical methods.

Ultrasonic sensors are used in applications where optical sensors perform poorly:

  • Black liquor and dark industrial effluents where infrared absorption is high
  • Samples with high volatile fatty acid (VFA) content where optical properties change rapidly
  • Return activated sludge (RAS) lines where concentration may exceed 10,000 mg/L

Measurement range for ultrasonic sensors is typically 200–100,000 mg/L, making them suitable for thickener underflow and sludge dewatering process monitoring as well as MLSS.

Microwave Sensors for Sludge Density

Microwave transmission sensors are used for high-concentration sludge measurement in thickening and dewatering applications (1–10% TS). They are not typically used in the low-MLSS range (2,000–5,000 mg/L) of activated sludge aeration basins.

Capacitance and Dielectric Sensors

Some MLSS sensor designs use changes in dielectric properties of the mixed liquor to infer suspended solids concentration. These sensors are less common in activated sludge applications and are more typically seen in food and beverage process monitoring.

Installation Configurations for Activated Sludge MLSS Monitoring

Submersible Probe Installation (Aeration Basin)

The simplest installation approach is a submersible NIR sensor mounted directly in the aeration basin on a fixed bracket or retractable mounting assembly. Key installation requirements:

  • Immersion depth: 0.5–1.5 m below the water surface, in the zone of active mixing. Avoid the surface (foam and floating materials) and the very bottom (settled solids zones near diffusers)
  • Flow velocity past sensor: NIR sensors require a minimum velocity of approximately 0.3 m/s past the measurement window to prevent sedimentation on the optical surface. In low-velocity zones, a flow deflector or mounting in a high-turbulence area near aeration equipment is recommended
  • Cleaning frequency: Most modern submersible MLSS sensors include compressed air wiper or ultrasonic cleaning systems that fire automatically before each measurement or on a timed cycle. Without active cleaning, biological and mineral fouling on the optical window causes signal drift within days
  • Cable management: Use cable strain relief to prevent fatigue at the sensor connection; allow slack for retraction during maintenance without pulling on the transmitter

Flow-Through Cell Installation (RAS Line)

Installing an MLSS sensor on the return activated sludge (RAS) line provides a representative measurement of the settled biomass concentration returned from the secondary clarifier. RAS MLSS is used to calculate actual SRT when combined with aeration basin MLSS and volume data. Flow-through cell installation requirements include:

  • Design flow velocity: 0.5–2.0 m/s through the cell to prevent settling
  • Sample flow: Take a sidestream bypass from the main RAS pipe; avoid direct in-line installation in large-diameter RAS pipes (sensor window too small relative to pipe diameter)
  • Bypass flow regulation: Install flow control valve to maintain constant velocity through the measurement cell
  • Vent point: Include a vent at the top of the flow cell to prevent air bubble accumulation that would cause erratic readings

Multiple Zone Monitoring

Large activated sludge systems with multiple parallel trains or biological nutrient removal (BNR) processes benefit from MLSS sensors in each zone:

For MLSS analyzer selection for activated sludge process control, contact Sechang Instrument. Contact our specialists →

  • Anoxic zone MLSS: Monitoring in the denitrification zone confirms adequate biomass for nitrate removal
  • Aerobic zone MLSS: Primary control point for aeration demand and SRT calculation
  • Secondary clarifier sludge blanket: Dedicated sludge blanket level sensors (or submersible MLSS sensors at multiple depths) detect early clarifier upset conditions
  • WAS/RAS flow monitoring: Combining flow measurement with MLSS measurement at the WAS and RAS discharge points enables mass-balance-based SRT control

MLSS-Based Sludge Retention Time (SRT) Control

The most advanced implementation of online MLSS monitoring is closed-loop SRT control. This approach uses continuous MLSS data combined with flow and volume measurements to calculate actual SRT in real time and adjust the WAS pump operation to maintain target SRT.

The SRT control algorithm:

  1. Measure MLSS in aeration basin and in WAS discharge flow
  2. Calculate current biomass inventory: MLSS (mg/L) × basin volume (m³) = total biomass (kg)
  3. Calculate WAS rate needed to achieve target SRT: WAS flow (m³/day) = total biomass (kg) ÷ [WAS MLSS (mg/L) × target SRT (days)]
  4. Adjust WAS pump speed via VFD to maintain calculated WAS rate
  5. Update calculation every 15–60 minutes using latest MLSS readings

Benefits of SRT-based control compared to manual WAS adjustment:

  • Maintains stable nitrification during seasonal temperature changes by automatically extending SRT in cold weather (nitrifier growth rate decreases below 15°C)
  • Prevents bulking sludge caused by overly long SRT (filamentous organisms dominate above ~20 days SRT in many systems)
  • Reduces operator labor — daily or twice-daily manual MLSS testing replaced by automated monitoring
  • Enables rapid response to changes in influent loading (storm events, industrial pretreatment upsets)

Calibration Protocol for MLSS Sensors

Unlike pH or dissolved oxygen sensors, MLSS sensors cannot be calibrated against a standard solution — the calibration is always site-specific, based on the actual relationship between optical/ultrasonic signal and gravimetric suspended solids in the specific mixed liquor.

Initial calibration procedure:

  1. Allow the sensor to reach operational equilibrium (24–48 hours in the process) to stabilize fouling layer and signal baseline
  2. Collect 3–5 grab samples simultaneously with sensor readings across a range of MLSS values (if possible: at normal operating MLSS and at elevated/reduced MLSS during a process upset or deliberate adjustment)
  3. Analyze grab samples by laboratory gravimetric TSS method (APHA 2540D): filter through glass fiber filter, dry at 105°C, weigh before and after
  4. Plot laboratory TSS values against sensor signal readings; apply linear regression or manufacturer-provided calibration curve
  5. Enter calibration coefficients in the transmitter

Recalibration frequency: Verify calibration against laboratory grab samples monthly, or whenever influent characteristics change significantly (industrial discharge changes, seasonal runoff events, major process modifications). Sensor fouling and biological film accumulation on optical windows are the primary causes of calibration drift.

Common MLSS Measurement Challenges and Solutions

Optical Window Fouling

Problem: Biofilm and mineral deposits on the sensor window cause the measured backscatter signal to increase over time, resulting in apparent MLSS increases that do not correspond to actual solids concentration changes.

Solution: Automatic compressed-air cleaning (firing a burst of 4–6 bar air across the optical window before each measurement) is the most effective approach. Verify cleaning effectiveness by checking that readings return to expected levels immediately after cleaning and that the pre-cleaning/post-cleaning reading difference is below ±5%.

Low-Velocity Dead Zones

Problem: In low-mixing zones or at the end of plug-flow aeration basins, sedimentation near the sensor reduces the local MLSS reading below the true bulk concentration.

Solution: Relocate the sensor to a higher-turbulence zone, add a mixing impeller near the sensor, or install the sensor on a swiveling arm that can be repositioned without draining the basin.

Foam and Surfactant Interference

Problem: Foam accumulation in aeration basins introduces air into the sample path, causing erratic high readings when air bubbles pass the optical window.

Solution: Install sensors below the foam zone (typically >1 m depth). If foam is persistent and deep, use a submerged flow-through housing that draws sample from below the foam layer.

Correlation Between MLSS and MLVSS

Problem: Process control algorithms based on MLVSS (organic fraction) require a stable MLSS-to-MLVSS ratio. Inorganic solids from chemical precipitation (phosphorus removal with alum or ferric) can increase MLSS without increasing active biomass, causing SRT calculations based on MLSS to overestimate actual biological sludge age.

Solution: Periodically measure MLVSS as well as MLSS; track the VSS/TSS ratio. Adjust SRT control setpoints when the VSS/TSS ratio changes significantly due to chemical addition.

Selecting an MLSS Analyzer

Key specification criteria for MLSS sensor procurement:

  • Measurement range: Confirm the specified range covers your expected MLSS at both startup (when MLSS may be 500–1,000 mg/L during seeding) and normal operation, plus RAS concentrations (typically 6,000–12,000 mg/L)
  • Cleaning system: Compressed air cleaning is preferred for activated sludge; ultrasonic cleaning or mechanical wiper systems for applications where compressed air cannot be supplied
  • Immersion rating: Verify IP68 rating and maximum submersion depth for basin installations
  • Cable length: Standard cable lengths (5–10 m) may be insufficient for deep basins or remote mounting — verify maximum cable extension and signal loss
  • Communication output: 4–20 mA analog output for standalone control; RS485/Modbus or Profibus PA for integrated SCADA systems with multiple sensors
  • Local display: Sensors with integrated local display simplify field calibration and troubleshooting without requiring laptop or SCADA access

Conclusion

Online MLSS analyzers and sludge concentration meters provide the data foundation for modern activated sludge process control. By replacing manual sampling with continuous measurement, wastewater treatment facilities can implement responsive SRT control, reduce energy consumption through optimized aeration demand, prevent nitrification failures in cold weather, and respond proactively to clarifier upset conditions. The investment in reliable online MLSS monitoring delivers operational benefits across plant capacity, effluent quality, energy efficiency, and operator workload reduction that manual monitoring simply cannot match.

Implementing reliable online MLSS monitoring requires matching sensor technology to your process conditions and aeration control strategy. Consult our process instrumentation specialists for MLSS sensor selection, aeration control integration, and SRT management support for your wastewater treatment plant.

Contact Sechang Instrument for MLSS analyzer and sludge concentration meter selection.

▶ Request a Quote